|
|
 |
|
|
|
|
|
|
|
|
|
|
|
Super Nerfs |
|
 |
 |
|
If you want "Real Rocker Protection" then
look no further! Absolutely hands down, the nicest and most
effective protection you can find for your Jeep®. They will support
the full weight of your vehicle without damage and you can even use
your "HiLift" jack on them without worry. They work great for
keeping the body off of rocks and trees. After having them on your
Jeep® you will find them great for pivoting around obstacles and you
will come to rely on them frequently. The backbone of the SuperNerf™ is the 2 x 2 x 3/16" square tube. It attaches to the pinch weld and supports the underside of the rocker panel from wheel to wheel. That allows any impacts to be distributed over a very large area eliminating damage to the rocker panels. They bolt into the pinch weld in several locations and also tie into the uni-body in two locations giving incredible strength. The outer tube is made from 1 1/4" x .140 wall pipe (which has a 1 5/8" OD) and is situated outside the body contour so it can be used as a true "nerf" bar. You can slide both tubes over or against any kind of obstacle all day long without damage to the rocker panels. The last feature, which sets our "SuperNerfs™" apart from all the copies, is the two small supports which tie the inner and outer tubes together giving an incredible amount of side load strength. Our "SuperNerf™" bars come powder coated in satin black. Yes, you will scratch them up when off-roading but semi-flat spray paint matches quite well. SuperNerfs™ are designed for bashing on rocks ultimately saving expensive body damage to your vehicle. They will pay for themselves the first time out! |
|
|
PART # 4WD-ZJP007 (1993 - 1998 ZJ) PART # 4WD-WJP007 (1999 - CURRENT WJ)
Please note that the SuperNerfs for XJ are pictured above. The ZJ version is nearly identical!! |
|
|
|
|
|
ACOStm Adjustable Coil Spacers |
|
 Photo courtesy: JKS MFG |
The "Adjustable Coil Over
Spacer" or "ACOS™" system allows you to easily fine tune or adjust
your suspension system to accommodate the added weight of bumpers,
winches, sagging springs or tire size changes. The system allows you
to level the vehicle front-to-back, or side-to-side. There is a
minimum of 1.25" of lift built into the "ACOS™" system and allows
for a maximum of 4-1/2" lift. Fits all ZJ- Sold in Pairs, Fits
ZJ Front Only.
PART # ACOS-F (ALL ZJ) |
|
|
||
| Adjustable Track Bars | ||
 Photo courtesy: JKS MFG |
||
|
The JKS Manufacturing adjustable trackbars
allow you to easily center your front axle under your Jeep. One turn
of the adjuster shifts the axle by approximately 1/16 inch at a time
so you may fine tune your axle center very precisely. A perfectly
centered axle is important to have for proper steering and "Quick
Disconnect" operation. The body of the trackbar is made from 1.25" x .156 DOM tubing, bent to proper angles for various lifts. A rebuildable "johnny joint" is used at the frame end, which also happens to be greasable. A tapered sleeve is then provided to fill the remaining taper. At the axle end you will find a zinc plated adjuster using the factory OEM style rubber bushing to reduce bushing "noise" transfer. The body is then flat black powder coated for corrosion protection.
|
||
| Part # 4WD-OGS125 |
Front Track Bar - Fits '84 -Present XJ, ZJ
and TJ with 4" or more of lift.
|
|
| Part # 4WD-OGS126 | Front Track Bar - Fits '84 -Present XJ, ZJ and TJ with 1" to 3.5" of lift | |
|
|
||
| Mini Skids | ||
 Photo courtesy: JKS MFG |
Designed to be welded to the front OEM lower
control arm brackets. When welded on, they will add much needed
strength to the brackets and act as a skid plate to protect the
brackets and control arm bushings from rock damage. They are made
from 1/4” thick plate and come in raw steel form as they do need to
be welded in place.
|
|
 Photo courtesy: JKS MFG |
Part # 4WD-OGS115 Fits: XJ, TJ, and ZJ front axles, all productions years |
|
|
|
||
| Jeep ZJ - Rubicon Series Front Bumpers | ||
|
Constructed of 3/16" Steel. Attaches through the six stock holes in the unibody rails. (frame) Heavy -duty clevis tabs are standard. All bumpers are shipped bare steel with no paint or powdercoat. |
||
|
|
||
 |
||
|
The Basic Front Bumper for ZJ Cherokee (XJ PICTURED). Includes winch mounting holes. Fairlead mount or 8274 Mount required for winch installation. Part # 4WD-ZJ-B (Bumper only) Part # 4WD-ZJ-FLM Winch Ready - (Basic Bumper with bolt-on planetary fairlead mount) Part # 4WD-ZJ-8274-WM (Bumper with 8274 Winch Mount)
|
|
|
|
||
|
The same Basic Bumper with a Winch Guard. The winch bar is the same radius as the Prerunner Hoop but with less overall height. Part # 4WD-ZJ-4 (Bumper with Winch Guard)
|
|
|
|
||
|
Optional Components:
Part # 4WD-8274-WM - Warn 8274 Mount, 4.5" X 10" pattern for four 3/8" bolts with 2 more holes spread 17"
Part # 4WD-FLM - Fairlead Mount, Fits any planetary winch up to 9500 lbs. with 4.5" X 10" bolt pattern
|
||
|
|
||
|
|
||
|
|
||
|
Copyright 4WD Products 2004
|
||
Made in U.S.A.
